RECOMMENDED GATEWAY SETTINGS FOR RFC SYSTEM PROTECTION
SAP BASIS
Select the transport order from the development system that was rejected in the quality system. This is technically repackaged into the Q-System in a new order and transported to the quality system. At this point you will again have the possibility to perform the approval step you really want to perform.
If you want to skip the backgrounds and prefer a direct step-by-step guide, you can jump directly into the last section. Preparation For this workaround, you need access to both the source system and the BW system. In addition, they shall have the possibility to access the SE37 and execute functional modules there. Especially in production systems this is a very critical justification. So assume that you may need a Firefighter user for this action. Working in the BW system Now that the preparations have been completed, you have to call a FuBa on the BW system and on the source system, which solves the connection on the respective page. Beginning on the BW system, go into the transaction SE37 and call the function block "RSAR_LOGICAL_SYSTEM_DELETE": RSAR_LOGICAL_SYSTEM_DELETE Enter the required values here. The following table helps you fill in: Field Description I_LOGSYS The logical name of the source system. The name of the source system, as found in RSA1, will be entered here. In addition, this name can also be found in the DB table TBDLT. I_FORCE_DELETE Boolean, X = Delete despite error messages I_NO_TRANSPORT Boolean, X = This change should not be transported to subsequent systems I_NO_AUTHORITY Boolean, X = Ignore Permission Checks Work in the source system In the source system, go to transaction SE37 and call the function block "RSAP_BIW_DISCONNECT" : The descriptions of the fields are as follows. These can be found in the RSBASIDOC source system connection table Field Description I_BIW_LOGSYS The logical name of the BW system. In the RSBASIDOC table, find the correct value in the column "RLOGSYS". I_OLTP_LOGSYS The logical name of the source system. The column ‘SLOGSYS’ in the table RSBASIDOC. I_FORCE_DELETE The logical name of the BW system. In the RSBASIDOC table, find the correct value in the column "RLOGSYS". Completion In the end, you have to call the respective function block in the BW and source system, fill in the parameters and execute the function block.
Double stack split
You wanted to rush to release a transport order in the quality system of your SAP landscape and accidentally clicked on "Reject" instead of "Approve"? Now the order cannot be transported any further and will soon be cleared by job from the queue? Don't despair: In this blog post, I'm going to tell you a simple way to get rejected transportation to the production system anyway. As a reader of our blog, you are certainly interested in tricks and tricks that will make your SAP system easier to handle. You may be aware of the situation where you want to approve a transport order quickly after the test has been completed and you have clicked in the system when the order was released. The problem now is that the transport order in the system now has a status of "rejected" and can therefore no longer be transported. In total, a transport order may receive important changes that you would have liked to have transported to the production system. Approach to release rejected transport orders The screenshot below shows the situation in the STMS transaction where a transport order in the quality assurance area was rejected. Therefore, an import into the production system is no longer possible. The transport job can be removed either manually or through a job. The question here, however, is how the amendments which were wrongly rejected can be transferred to the subsequent system. Rejected Transport Order Tip: Leave the status on Rejected, remove the rejected transport order from the import queue, if necessary, and follow the next steps. Switch to the import queue in your quality system. Go there via Additions -> More Orders -> Attach to the modal window where you can perform further steps.
QUEUE_STILL_IN_BUFFER: The queue is not fully processed because incomplete support packages of the queue are still in the transport buffer. CANNOT_RESET_FCS_FLAG: If there is an FCS Support Package (FFD) in the queue, the system will be marked as being at the generally available release level after this support package is inserted. In this case, this operation could not be performed successfully.
"Shortcut for SAP Systems" simplifies tasks in the area of the SAP basis and complements missing functions of the standard.
The SAP basis sees itself as a partner and contact for new SAP technologies.
Understanding the structure and functioning of the system is especially important for IT administration. It is not for nothing that "SAP Basis Administrator" is a separate professional field. On the page www.sap-corner.de you will find useful information on this topic.
The scope of the check of system settings and system security includes not only the SAP Basis settings presented here, but also other SAP Basis settings.